Trianglelab PT1000 Thermistor Cartridge for 3D printer Volcano/ v6 heater block UPTO 450C PEEK PEI PT100 printing

100 % of buyers enjoyed this product!
Availability: in stock
Ships From: Russian Federation China
Price:  US $9.90
Sale Price:  US $8.41
from AliExpress
45 days Money back 45 days Money back Returns accepted if product not as described, buyer pays return shipping; or keep the product & agree refund with seller.
On-time Delivery On-time Delivery
Guarantees: On-time Delivery 60 days

If you need to send UPS/Fedex/TNT/DHL, please contact us.We need to discuss the freight with you.
The trianglelab has always been concerned about product quality.We are developing products and working hard to improve the quality.We will not abandon our reputation because of many cheap products on the market.It is believed that only high quality products can ensure the quality of your work and bring safety to your work.
Some of our products may be more expensive than others,but please believe in our quality and believe that you will not regret when you receive the goods.
***-***
***-***

***-***

Trianglelab Thermistor Cartrodge PT1000 for v6 hotend v6 heater block Maximum support to 450 degrees for Volcano heater block.
Trianglelab Thermistor Cartridge PT1000 Upto 450 degrees.
*Compatible V6 Heater Block(NEW)
*Compatible Volcano Heater Block
*PT1000 sensor is not compatible with Lerdge K motherboard
PT1000 sensors are able to measure higher temperatures than thermistors – upto 400°C,and are more accurate then both thermistors and thermocouples in general.
PT1000 sensors can direct replace the thermistors in your printer  without adding an amplifier board like PT100's sensors.
but whith the default 4.7K pullup resister on board you will get lower resolution than other sensors.
PT1000 sensors are compatible with most firmwares in the field.
PT1000 sensors are potentially a good cost and performance compromise between thermistors and PT100 sensors.
If you want release potential abilities of the PT1000 sensors,you need to replace the 4.7Kpullup resister of the thermistor pins with a 1K 0.1% resister.
operating temperature range 0-450 degrees
metal cartridge dimension 3MM diameter 15MM length
lead 1Meter length fiberglass High temperature resistant wire
RESISTANCE VALUE CHART PER 1C PT1000://www.hayashidenko.co.jp/en/info14.html
1 x PT1000 seneor with sealed with metal cartridge
3 x 1K 0.1% SMD Resistors 0603 package
1 x 2P 2.54MM Terminal wire
For duet2 Wifi, firmware 3.1, seetings as follows:
M308 S1 P”e0temp” Y”pt1000″ R2000 ;two 1K resistors in series for better accuracy
Marlin:
Default 4.7Kpullup resistor please choose sensor '1047'
If you have replaced pullup with 1K resistor please choose sensor '1010'
Configuration.h:
*1047 : Pt1000 with 4k7 pullup
*1010 : Pt1000 with 1k pullup(non standard)
#define TEMP_SENSOR_0 1010
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_BED 1
thermistortable_1010.h:
// Pt1000 with 1k0 pullup
const short temptable_1010[][2] PROGMEM = {
PtLine(    0, 1000, 1000)
PtLine(  25, 1000, 1000)
PtLine(  50, 1000, 1000)
PtLine(  75, 1000, 1000)
PtLine(100, 1000, 1000)
PtLine(125, 1000, 1000)
PtLine(150, 1000, 1000)
PtLine(175, 1000, 1000)
PtLine(200, 1000, 1000)
PtLine(225, 1000, 1000)
PtLine(250, 1000, 1000)
PtLine(275, 1000, 1000)
PtLine(300, 1000, 1000)
PtLine(325, 1000, 1000)
PtLine(350, 1000, 1000)
PtLine(375, 1000, 1000)
PtLine(400, 1000, 1000)
PtLine(425, 1000, 1000)
PtLine(450, 1000, 1000)
};
thermistortable_1047.h:
// Pt1000 with 4k7 pullup
const short temptable_1047[][2] PROGMEM = {
// only a few values are needed as the curve is very flat
PtLine(    0, 1000, 4700)
PtLine(  50, 1000, 4700)
PtLine(100, 1000, 4700)
PtLine(150, 1000, 4700)
PtLine(200, 1000, 4700)
PtLine(250, 1000, 4700)
PtLine(300, 1000, 4700)
PtLine(350, 1000, 4700)
PtLine(400, 1000, 4700)
PtLine(450, 1000, 4700)
};
Pt1000 with 4k7 pullup resistor(default)
Configuration.h:
#define NUM_TEMPS_USERTHERMISTOR0 12
#define USER_THERMISTORTABLE0{{723,0},{812,320},{896,640},{975,960},{1049,1280},{1118,1600},{1184,1920},{1246,2240},{1305,2560},{1361,2880},{1414,3200},{1464,3520}}
Pt1000 with 1K pullup resistor
Configuration.h:
#define NUM_TEMPS_USERTHERMISTOR0 23
#define USER_THERMISTORTABLE0 {{2055,0},{2132,160},{2202,320},{2327,640},{2383,800},{2436,960},{2485,1120},{2531,1280},{2574,1440},{2614,1600},{2653,1760},{2689,1920},{2723,2080},{2755,2240},{2786,2400},{2815,2560},{2842,2720},{2869,2880},{2894,3040},{2918,3200},{2940,3360},{2962,3520},{2983,3680}}
You can also set up a new USER_THERMISTORTABLE in their web firmware configuration tool.
R2 is the pullup resistor of thermistor pins.
M305 P1 X501 R4700;heater 1 uses a PT1000 connected to thermistor channel 1 which has a 4.7K series resistor
M305 P1 X501 R1000;heater 1 uses a PT1000 connected to thermistor channel 1 which has a 1K series resistor
Working on it please refer to
You can choose PT100 and amplifier board instead,if you need more than 300C temperature.Please clickhere
TIPS:You can use the temperature input pin P0.23-P0.26 by remove the pullup resistor of that pin.When you connect the PT100 amplifier board to your smoothieboard or MKS SBASE.(we already tested it works)
1.Try to find any 472 or 4701 marks 'Rx' resistor near the thermistor input terminals.
2.Measure the 2pins of the terminal with a multimeter one pin should short to GND/AGND one should short to the one end of the pullup resistor
3.Replace it with your soldering iron and skills
4.Connect the PT1000 sensor like normal thermistor
5.Make the change to your firmware
6.If everything goes well the printer should show the room temperatures
***-***
If you want the thermistor sensor that can fits on your hotend please click below.

Compatibility demonstration
//duet3d.dozuki.com/Wiki/Connecting_thermistors_or_PT1000_temperature_sensors

Size:

Shipping Company Shipping Cost Estimated Delivery Time
DHL 3 - 7 days
UPS Expedited 3 - 7 days
EMS 5 - 14 days
Post Air Mail Free Shipping 15 - 45 days
Return Policy If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.

N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
Seller Service On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).

Most Popular from Category


Price:  US $9.90
Sale Price:  US $8.41
from AliExpress